Search results

Aww come on JB! You can't hold out on us.

https://www.use-ip.co.uk/forum/threads/this-channel-has-no-substream.12289/ https://www.use-ip.co.uk/forum/threads/h264-265-265-hell.12366/

New cam still working perfectly. Old cam was crap. The "other" forum has a post about corrupted partitions on the cam that can't be cured, causing problems. In any case, as always, my posts are meant for posterity for anyone encountering similar problems.

@JB1970 as a follow up to previous posts about that one G2 that never, ever, ever gives intrusion detections - I just swapped it out with a new, identical G2 and it works perfectly. There was something wrong with that camera, despite multiple firmware upgrades/downgrades, that prevented it from...

No idea what I did wrong, JB. My system worked flawlessly for years, but I can't leave well enough alone. Just had to try out a couple of G2's (disaster) and then playing around with settings on all the cameras. When all those errors starting showing up, I just put everything back to where it...

I have a 7608-I series with the following cameras: (1) 2347 G2 (2) 2387G2 (4) 2347 G1 (1) 2455 G1 I tend to tinker with settings, and recently have been getting lots of errors relating to "no substream available" and "not enough resources." Going through each camera's settings, for both main...

One of my other G2's, at my front door, the intrusion detection has never, ever worked. Line detection is great. But intrusion is just completely busted. Firmware, reboot, factory reset, rebuild, nothing. It just doesn't work. I'm about to throw it in the garbage and go back to my 2347G1 at that...

Much appreciated JB!

Link please to the smart search? Does this only work on the monitor, or will it work on web interface too? I can't seem to get it to work, but it's the first time I've tried using this feature.

After reading the comments by @JB1970 in this thread: https://www.use-ip.co.uk/forum/threads/firmware-upgrade-confusion.12293/ I downgraded this troublesome camera from 5.7.19 to 5.7.15 and it completely fixed the problem. No idea why. When I reloaded 5.7.19 it went back to the same substream...

This is on a fairly new (to me) DS-2CD2387G2-LU on 5.7.19. Hooked to a 7608 I-series on 4.61.020. Out of the blue, with no changes on my part, I am now getting this message when doing the 3x3 live view. My other 7 cameras are fine. In camera management live view works just fine, as it does in...

@maionline, I've got several DS-2CD2387G2-LU's on 5.7.17 and "supplemental light" toggle is there - if that helps any.

I've been using a similar camera, a 2455, for about 5 years. It's never set off an alarm after being powered on. I didn't even know it was capable of doing that. They're super easy to take apart. Open it up and rip out the buzzer/speaker thingy.

Kinda makes you miss the "obsolete" I-series, doesn't it?

I followed the advice in this thread.

I appreciate this post. I just installed a new camera (2387G2) that had these floating numbers/letters above moving objects. Strange, because I've rotated about 15 cameras through my system over the last 5 years and never had this issue, but I got it fixed. Thanks to all.

I found this old thread: https://www.use-ip.co.uk/forum/threads/how-the-you-setup-the-correct-time.1977/#post-5924 Unfortunately, the "how to" thread referenced in the one above has all of the screen shots deleted at this point, so I'm not sure how much it's going to help.

All of my cameras have the following: Bitrate type: variable Video quality: highest Frame rate: 25 Max bitrate: 8192 Max average bitrate: 4096 All are on H265+ So given all this, how would I calculate what my incoming bandwidth is, and how much margin I have? I understand that the I-series has...

I have a 7608 I-series 8 channel NVR. Connected are (6) 2347 G1's that are 4MP, (1) 2347 G2 that is 4MP, and (1) 2CD2455FWD cube camera that is 5MP. I want to remove one of the G1's and replace it with a 2387G2 8MP. It got me thinking about whether my NVR can handle the extra incoming bandwidth...

@Kyle what is that plugin you reference above and what does it do? I've not heard of that one before.