01304 827609 info@use-ip.co.uk Find us

Recent content by ekkostar

  1. E

    IPC-B650Z Foggy Lens?

    Quick update. I took the cameras down, opened them up and gave them a good wipe down. Added a few new well placed silica bags for good measure. I did not apply Clear Vue internally due to the sponge. Instead I applied it on the outside/weather facing side of the glass. So far all camera's...
  2. E

    IPC-B650Z Foggy Lens?

    Do you think adding a wipe of Rain X or ClearVue on the inside of the lens cover may help as well. I guess that along with a full dry out and new desiccants will make it bombproof over it's expected life. Cameras are not the sort of thing I wish to be continually removing and drying out...
  3. E

    IPC-B650Z Foggy Lens?

    Ok great, will order some desiccant bags. For the schematics it looks like straightforward access to the inner of the lens cover. Hopefully, that's all that is needed. The cameras are brand new so was a bit surprised this is how they are shipped?
  4. E

    IPC-B650Z Foggy Lens?

    Thanks Dan, I noticed that on a zoomed photo but it was not so clear just looking at it. So, you think I could just unmount the camera, unscrew the lens cover off and leave the two halves to dry near a radiator. That should resolve it pretty quick right. Maybe add a few new desiccant bags in...
  5. E

    IPC-B650Z Foggy Lens?

    It has this sticker over the seam
  6. E

    IPC-B650Z Foggy Lens?

    Hi Dan, The micro SD is inside the camera housing. In order to get the front cover (1) off it needs to be unscrewed. However, underneath it has a tamper seal on the seam of front and rear housing (1+7). So any unscrewing will tear the tamper seal. I am guessing this would invalidate warranty.
  7. E

    IPC-B650Z Foggy Lens?

    Hi, So I got these cameras IPC B650 Z On set up and installation they have immediately developed foggy lens and condensation inside the glass. Great :-( Is there a way to fix this ? I understand there are ways to address the problem by opening up the camera but as it is brand new and...
  8. E

    Hilook IP camera - can't access it from the browser?

    Then a good old fashioned reset and start again I guess
  9. E

    Hilook IP camera - can't access it from the browser?

    Have you checked your Network and IP leases? Are you clashing with another existing IP address ? Try DHCP instead
  10. E

    Hilook IP camera - can't access it from the browser?

    Click add device to list and then try from there- Also why in SADP is your IP address for the camera 192.168.1.226 ? Have you changed it manually or are you using DHCP to get the 192.168.1.137?
  11. E

    Hilook IP camera - can't access it from the browser?

    Click the grey box at the bottom where it says "Online Device" Is your camera activated?
  12. E

    Hilook IP camera - can't access it from the browser?

    1. Tick the box 2. Click on refresh Your network status will go Online and Green Bingo !
  13. E

    Hilook IP camera - can't access it from the browser?

    If I go by Edge, Chrome or any browser it will give the 'notSupported.asp' return and you cannot access the camera configuration etc If you install HiTools Delivery it will see all your online cameras. You can see the IPC-650H Z circled. 1. Tick the box on the left 2. Click on the setup...
  14. E

    Hilook IP camera - can't access it from the browser?

    Ok I've had a similar issue with a new HiLook. My camera is a IPC-B650H Z It will not allow access from a browser, so sounds like the same problem. Set it all up properly.... SADP, assigned new IP, strong password. In fact it would not even allow access even on default 192.168.1.64 either...
  15. E

    Hikvision Unmanaged Switches DS-3E0526P-E vs DS-3E0518P-E?

    Many thanks for that Dan. The 16 port and above Hikvision switches do look identical to other business class network switches that are available and they do appear to have 2 fans on board. Network switches I understand can certainly be louder than a NVR and the concern with the 2 fans here is...
Back
Top